Metal furniture guide
How to clean metal garden furniture
Clean powder-coated aluminium and painted steel garden furniture without lifting finishes. Spot rust, protect joints and choose safe aftercare.

Aluminium, steel and cast iron have different weak points
Aluminium frames do not develop red iron rust, but their coating can still chip and fittings may be steel. Painted and powder-coated steel can corrode where water reaches bare metal. Cast iron is heavy, often decorative and may have a multi-layer paint system. Check the maker's care instructions and whether the frame is safe to move before washing.
Fabric slings, timber arms and plastic caps on the same chair may need a separate cleaner. Avoid spraying directly into hollow tubes or around spring-loaded reclining hardware. For the other materials, see the garden furniture overview.
Wash coated metal without scratching it
- Remove cushions and brush off dry grit from arms, undersides and joints.
- Inspect chips, flaking paint, loose screws and sharp rust before wetting anything.
- Test a mild metal-furniture-compatible cleaner where it will not show.
- Wipe with a soft clean cloth, working around decorative details without abrasive pads.
- Rinse as the cleaner label requires; use only enough water to clear residue.
- Dry seams, welds and feet. Replace any missing foot caps so bare metal is not left on damp paving.
HG's outdoor-furniture cleaner lists aluminium and coated metal among its intended surfaces. That does not override the furniture maker's instructions, particularly on damaged powder coat or a special finish. For ordinary dust, warm water and a soft cloth may be sufficient.
Separate cleaning from rust repair
Orange staining around a screw may come from one steel fitting rather than the whole frame. Identify the source and let the area dry. If paint is bubbling, merely wiping it clean will not stop corrosion underneath. Use a metal-preparation and repair system that matches the frame, or seek repair advice for structural legs and welded joints. Do not paint over active loose rust or wet metal.
Never aim a concentrated pressure jet at a chipped coating: it can lift the edge and force water beneath it. A covered, ventilated storage spot and dry foot caps do more for longevity than harsh seasonal cleaning. Wooden arms on a metal chair need their own wood-care method.
Soft-contact cleaning for sound coatings
HG cleaner is an option for compatible coated frames; soft cloths help keep grit away from the finish. Neither product repairs chipped powder coat or rust. Patch-test and follow both maker and cleaner instructions.
HG Garden Furniture Cleaner 500ml
Best for: Maker-approved plastic, aluminium and coated-metal garden furniture
A furniture cleaner listed for several non-wood outdoor materials. Test a hidden patch, respect the finish and follow the label's dwell and rinse directions.
Confirm the exact furniture material and coating before use, especially around damaged paint or plated hardware.
- 500 ml
- Outdoor furniture
- Plastic and coated metal
- Patch test
Amazon Basics Microfibre Cleaning Cloths, 24-pack
Best for: Separate soft cloths for low-water cleaning and drying of accessible surfaces
A multipack of reusable microfibre cloths for controlled hand cleaning. Keep clean cloths separate by task, and never drag grit across paint or electrical contacts.
Useful for careful wiping, not a substitute for a paint-safe wash mitt on gritty car bodywork.
- 24 cloths
- 40.5 × 30.5 cm
- Reusable
- Keep grit separate
Frequently asked questions
Can I pressure wash powder-coated furniture?
A soft cloth is safer. Jets can exploit chips or force water into tube ends; follow the furniture maker's guidance.
Does aluminium garden furniture rust?
Aluminium does not make red iron rust, but steel screws can and its coating can still be damaged.
How do I clean metal chair joints?
Brush loose grit, wipe with a compatible cleaner and dry thoroughly without flooding hollow sections.
Can I paint over small rust spots?
Not directly. Assess how far corrosion extends and use a compatible surface-preparation and coating system on sound, dry metal.
What cleaner should I avoid on coated metal?
Abrasive pads and unapproved strong solvents can damage the finish. Use the maker-approved mild option first.