Skip to content

Maintenance guide

How to clean a pressure-washer nozzle and inlet filter

Clean removable pressure-washer nozzles and inlet screens without damaging the jet or running the pump unfiltered; know when to replace a part.

Gloved hands rinsing detached nozzle and mesh inlet strainer at a sink

Bosch's UniversalAquatak manual covers nozzle and filter cleaning as user maintenance and says to switch off and disconnect the machine before adjustment or cleaning. Read Bosch's maintenance instructions.

Make the washer safe before removing anything

Cleaning a removable inlet filter is a small job; releasing pressurised water unexpectedly is not. Follow the model's complete shutdown order: turn off, unplug, close the tap and use the gun to release residual pressure where the manual directs. Wait for moving parts to stop. Never disconnect a high-pressure hose or lance simply because the switch is off.

Identify the inlet screen on the water-supply side and the spray nozzle at the end of the approved lance. Do not confuse them with internal pump filters, sealed valves or an integrated detergent system. If the manual does not describe user removal, leave the part in place and ask the maker.

Rinse the inlet screen without tearing it

Remove the accessible sieve with the tool or method specified by the manufacturer. Kärcher's K 4 manual describes gently withdrawing the water-connection sieve, rinsing it under running water and returning it without using hard or sharp objects. Bosch likewise requires its inlet filter to remain clean and fitted. A soft stream of clean water is safer than pushing grit through the mesh or scraping the frame.

Check for cracks, stretched mesh, a displaced seal or a damaged transparent filter bowl. A clogged optional filter can restrict supply and cause pulsing or low pressure. Refit every required screen before starting; do not remove it as a shortcut to increase flow.

Inlet protection Kärcher clear water inlet filter

Kärcher K-Series Water Filter

Best for: Filtering small particles from an approved water supply before a Kärcher K-series pump

A transparent inlet-side filter for the K 2–K 7 domestic range. It catches particles, but does not make dirty, chemically contaminated or unsuitable water safe for the washer.

An optional extra where the machine instructions and water source justify it; first inspect and clean any filter already built into the washer.

  • Inlet side
  • Part 4.730-059.0
  • K 2–K 7
  • Check existing filter

Clean the nozzle by the maker's method

Inspect the detached nozzle for visible grit, scale or a distorted spray opening. Flush from the direction specified by the manual. Some kits include a dedicated cleaning pin, while other makers warn against hard or sharp objects; use a pin only when that exact nozzle's instructions allow it. A sewing needle or drill bit can permanently enlarge the opening and change pressure and spray shape.

Do not soak unknown seals in descaler or chemical cleaner without maker approval. If flushing does not restore the spray, or a nozzle is cracked, replace it with an exact model-compatible part. A fan, rotary and detergent nozzle are not interchangeable just because their connectors look alike; see the nozzle guide.

Refit, prime and make one controlled test

Seat the filter and nozzle fully, reconnect water, open the tap and check accessible inlet joints for leakage. Vent air by the exact washer procedure before applying high pressure. Test on a robust, inconspicuous surface with a broad fan and appropriate distance. If the pattern remains irregular or the pump pulses, stop and move to fault-finding rather than repeatedly operating with a restricted supply.

The Kärcher external filter shown above is an optional K-series accessory, not a replacement for every internal screen. Confirm the part number and whether an extra filter is actually useful in our inlet-filter decision guide.

Frequently asked questions

How often should I clean the inlet filter?

Inspect it at the interval in your manual and sooner if flow falls, the source is stored water or visible grit is present.

Can I run the pressure washer without its filter?

No, not when the maker requires a screen. Debris can damage the pump.

Can I use a pin to clear the nozzle?

Only if the exact manufacturer instructions permit a specified cleaning tool. A random sharp pin may enlarge the jet opening.

Why is my spray pattern uneven after cleaning?

The nozzle may still be obstructed or worn, or air and supply flow may be the cause. Stop and check the water path.

Does an extra filter replace the built-in one?

No. Keep the built-in screen clean and fitted; an optional external filter has a separate, model-specific role.